Die Suche ergab 33 Treffer

von Hec In Omaha
Mi Sep 05, 2018 8:18 pm
Forum: Technical Discussions
Thema: Carb Setting
Antworten: 8
Zugriffe: 2834

Re: Carb Setting

Here is a picture of my AS600 with a Walbro Carb. I hope this helps!

Hec
Big Tex Carb.jpg
von Hec In Omaha
Do Jul 26, 2018 5:20 pm
Forum: Technical Discussions
Thema: Prop polishing
Antworten: 12
Zugriffe: 3242

Re: Prop polishing

I don't think your post is in regards to an Aquascooter. If you are referring to a boat prop, you will need to find one the physically fits so it needs to be the proper diameter. Next you will need the proper pitch so that the engine achieves the recommended Wide Open Throttle RPM's under normal con...
von Hec In Omaha
Fr Jul 06, 2018 4:59 pm
Forum: Technical Discussions
Thema: Exhaust change
Antworten: 3
Zugriffe: 910

Re: Exhaust change

I am on my second season after replacing the exhaust valves in 3 of my AS600's. So far so good!

Hec
von Hec In Omaha
Di Jul 03, 2018 10:53 pm
Forum: Technical Discussions
Thema: Hec's AS600 Rebuild
Antworten: 4
Zugriffe: 1201

Re: Hec's AS600 Rebuild

Here ya go!

Rear prop seals:

Seal nearest piston, spring faces piston.
Seal nearest prop spring faces prop.

Main seals:
Side without spring is against bearings

Hec
von Hec In Omaha
Mi Aug 30, 2017 2:11 pm
Forum: Technical Discussions
Thema: "Generic" parts
Antworten: 2
Zugriffe: 858

Re: "Generic" parts

All,

Here are some part numbers for the AS600. I get my parts locally and they are much cheaper than going through Aquascooter.

Cheers

Hec
von Hec In Omaha
Fr Aug 25, 2017 6:49 pm
Forum: Technical Discussions
Thema: Prop polishing
Antworten: 12
Zugriffe: 3242

Re: Prop polishing

As far as I know, all props are the same. They all have the same part number.

Here is another powder coated prop going in a rebuilt AS400 I'm putting back together.

Hec
von Hec In Omaha
Do Aug 24, 2017 3:27 pm
Forum: Technical Discussions
Thema: Starts great, runs great, 5 minutes later dies
Antworten: 12
Zugriffe: 2933

Re: Starts great, runs great, 5 minutes later dies

Man! I love it when a plan comes together! Just call me the Aquascooter Whisperer! :lol: Good Job!

Hec
von Hec In Omaha
Do Aug 24, 2017 3:21 pm
Forum: Technical Discussions
Thema: Starts great, runs great, 5 minutes later dies
Antworten: 12
Zugriffe: 2933

Re: Starts great, runs great, 5 minutes later dies

Great news! So did that solve the AS600 stalling issues? By the way, I have seen the same duck bill valves underneath weed wacker and chainsaw gas caps. If you have a source for old lawn equipment parts you may get lucky.


Hec
von Hec In Omaha
Do Aug 24, 2017 2:58 am
Forum: Technical Discussions
Thema: Starts great, runs great, 5 minutes later dies
Antworten: 12
Zugriffe: 2933

Re: Starts great, runs great, 5 minutes later dies

That AS 450 will require a complete tear down and reseal. I will replace all bearings, o-rings, seals, hone the cylinder ( if it isn't scored up bad),install new piston rings (if piston isn't scored up) on anything 5 yrs or older. 30 years of sitting will result in cracked seals. The rear prop shaft...
von Hec In Omaha
Mi Aug 23, 2017 2:59 am
Forum: Technical Discussions
Thema: Prop polishing
Antworten: 12
Zugriffe: 3242

Re: Prop polishing

All, My red and white AS600 has a powder coated prop. The finish is much smoother than the bare stock prop. My red and white AS600 is faster than my Daughters Yellow one. Even though it's an older orange tank version fitted with a new tank,cruise handle,and AS400 starter housing and tail piece. I wa...